Principle of work and design

ECOZHAR

The principle of operation of the furnace

The principle of operation of the Ekozhar Pro series furnaces is based on the forced convection of heated air. The fan draws cold air from the room and drives it through the coolant circulation chamber between the furnace and the outer casing. In this way, heat is removed from the heated firebox and transferred to the room through the outlet heat pipes. If it is necessary to transfer the heated air to an adjacent room, a metal corrugated pipe is used.

Blower and slide gate

A control valve - a slide valve - is installed in the inlet of the furnace. It allows you to precisely dose the amount of air entering the combustion chamber, thereby optimizing efficiency and increasing the time of fuel combustion on one full load. This damper allows you to precisely adjust the cross-section of the inlet pipe, which allows you to use the stove in two operating modes: combustion mode and smoldering mode.

Thickness of the furnace

In the Ekozhar Pro series, special emphasis is placed on the thickness of the furnace metal, which is 9 mm. The metal we use guarantees a service life of at least 10 years.

Outer casing

The casing is made of 1.5 mm thick sheet metal. This thickness was chosen for a reason. First, it is the optimal thickness that allows the structure to be rigid. Secondly, in this area, the metal is less susceptible to temperature effects than the metal of the furnace. Thirdly, if the casing wall is too thick, it will prevent good heat transfer to the room, which will reduce the efficiency of the furnace as a whole.

Secondary gas afterburner chamber

The principle of secondary gas afterburning is implemented in the Ekozhar Pro series furnaces. The secondary gas afterburner chamber is designed in such a way that it mixes oxygen from the air with the flue gases, and under the influence of an open fire, they ignite, generating additional heat. This increases the efficiency of the stove and its economy (more heat with less fuel).

Firebox door slide

The firebox door handle acts as a lock in the closed position. In this position, the door is tightly pressed, and due to the sealing cord along the contour of the door itself, flue gases cannot enter the room.

Coolant circulation chamber

The space between the walls of the furnace and the outer casing is the coolant circulation chamber. Due to the forced supply of air through the circulation chamber, heat is removed from the walls of the furnace evenly over the entire area. The circulation chamber is physically separated from the combustion chamber and prevents flue gases from entering the room.

Built-in fan

The location of the fan is chosen in such a way as to instantly take the coldest air in the room and, driving it through the coolant circulation chamber, transport it to the place where it is convenient for you, using corrugated or rigid ventilation ducts.

Watch a 2-minute video about the stoves of the “Ekozhar Pro” series

Stove potbelly stove Ekojar (formerly "Brest") Pro 700 Plus set with fan

The Ecozhar Pro 700+ heating furnace with built-in fan is designed for heating large rooms with an area of up to 300 m² and a volume of up to 700 m³.

The Ekozhar Pro 700+ heating furnace with a built-in fan is designed to heat large rooms with an area of up to 300 m² and a volume of up to 700 m³.

The power of this furnace model is 30 kW, which allows you to quickly warm up large spaces, including production halls, warehouses, or even large houses.

The efficiency is 91%.

Burning time on one full load of wood - up to 12 hours

Chimney diameter - 160 mm

The furnace furnace is made of thick-walled pipe, 7 mm thick. The casing is made of metal, 1.5 mm thick. This is enough for the stove to operate efficiently for more than one season and does not prevent good heat transfer to the room.

One of the key features of the furnace is the secondary gas afterburner system, which significantly increases fuel efficiency. The secondary gas afterburner chamber is designed in such a way that oxygen from the air is mixed with the flue gases, and under the influence of an open fire, they ignite, generating additional heat. This increases the efficiency of the furnace up to 91% and improves the furnace's economy.

The stove operates in two modes: combustion and smoldering. The combustion mode is used to ignite the stove and quickly warm up the room, and the smoldering mode maintains the set temperature after heating, significantly saving fuel. Switching between the modes and adjusting the intensity of combustion is carried out using two slide dampers on the door and chimney pipes.

There is a plate inside the firebox that helps to cool the gases before they enter the chimney, which increases the service life of the chimney and the stove as a whole. The stove door is equipped with a heat-resistant cord that prevents smoke from escaping into the room.

Integrated fan

This model is equipped with a fan that ensures fast and even heat distribution and allows you to achieve a comfortable room temperature in a short time.

The 59 W axial type blower fan.

The use of the fan allows to increase the efficiency of the furnace up to 91% and evenly distribute the heated air throughout the room.

Each series and model of our furnaces is developed by a designer to ensure maximum efficiency and productivity. We have mass production of furnaces, which guarantees the quality of each product. And all models of stoves have a certificate of conformity.

We are confident in the quality of our products and that you will be satisfied.

Our customers' feedback serves as confirmation for both us and you.

Below is only a small part of them.

Our heating stoves use an active heat circuit to distribute heat efficiently and maintain the optimum room temperature, as well as to increase the energy efficiency of the stove. The circuit consists of a combination of corrugated tubes and a fan connection for blowing around the firebox or around the furnace walls. Thanks to the active heat circuit, the stove can maintain stable heating even after combustion is complete, cooling down more slowly and releasing the accumulated heat. This reduces fuel consumption and ensures constant comfort in the room.Our heating stoves use an active heat circuit to efficiently distribute heat and maintain optimal room temperature, as well as to increase the energy efficiency of the stove. This circuit is a combination of corrugated tubes and a fan connection for blowing around the firebox or along the contour of the stove walls. Thanks to the active heat circuit, the stove can maintain stable heating even after combustion is complete, cooling down more slowly and releasing the accumulated heat. This reduces fuel consumption and ensures constant comfort in the room.

The thickness of the furnace

7mm

Heating volume

700m3

Heating area

300m2

Firebox size

1200х520mm

Warranty

12 months

External dimensions

1500х1000х630