Principle of work and design

ECOZHAR

The principle of operation

The principle of operation of the furnace The principle of operation of the Ekozhar Pro series furnaces is based on forced convection of the heated air. The fan draws cold air from the room and drives it through the coolant circulation chamber between the furnace and the outer casing. In this way, heat is removed from the heated firebox and transferred to the room through the outlet heat pipes. If it is necessary to transfer the heated air to an adjacent room, a metal corrugated pipe is used.

Blower and slide damper

A control valve, a slide damper, is installed in the inlet of the furnace. It allows you to accurately dose the amount of air entering the combustion chamber, thereby optimizing efficiency and increasing the time of fuel combustion on one full load. This damper allows you to precisely adjust the cross-section of the inlet pipe, which allows you to use the stove in two operating modes: combustion mode and smoldering mode.

The thickness of the firebox

In the Ekozhar Pro series, special emphasis is placed on the thickness of the firebox metal, which is 8 mm. The metal we use guarantees a service life of at least 10 years.

Outer casing

The casing is made of 1.5 mm thick sheet metal. This thickness was chosen for a reason. First, it is the optimal thickness that allows the structure to be rigid. Secondly, in this area, the metal is less susceptible to temperature effects than the metal of the furnace. Thirdly, if the casing wall is too thick, it will prevent good heat transfer to the room, which will reduce the efficiency of the furnace as a whole.

Secondary gas afterburner

The Ekozhar Pro series furnaces implement the principle of secondary gas afterburning. The secondary gas afterburner chamber is designed in such a way that oxygen from the air is mixed with the flue gases, and under the influence of an open fire, they ignite, generating additional heat. This increases the efficiency of the stove and its economy (more heat with less fuel).

Integrated heat exchanger

A is integrated in the casing. The door and the rear panel can be removed from both sides if necessary, so that it can be cleaned after prolonged operation. The diameter of the outlet is 300 mm.

Fins and coolant circulation chamber

The space between the furnace walls and the outer casing is the circulation chamber. By forcing air through the circulation chamber, heat is removed from the furnace walls evenly over the entire area. The circulation chamber is physically separated from the combustion chamber and prevents flue gases from entering the room. The furnace tube is finned over the entire area, which is hidden in the casing, making heat transfer most efficient by increasing the heating area.

The firebox door latch

The firebox door handle acts as a lock in the closed position. In this position, the door is tightly pressed, and due to the sealing cord along the contour of the door itself, chimney gases cannot enter the room

Fan

The location of the fan is chosen in such a way as to instantly take the coldest air in the room and, driving it through the coolant circulation chamber, transport it to the place where it is convenient for you, using corrugated or rigid ventilation ducts. You can purchase the fan separately, the production time is up to 14 days.

Wood stove industrial heater Ekozhar (formerly "Brest") Pro Max 2500

The Ekozhar Pro Max 2500 heating furnace is designed to heat large rooms with an area of up to 610 m² and a volume of up to 2500 m³.

The power of this furnace model is 60 kW, which allows you to quickly warm up large spaces, including production halls, warehouses, or even large houses.

The efficiency is 91%.

Burning time on one full load of wood - up to 18 hours

Chimney diameter - 200 mm

Design of the furnace Ekozhar Pro Max 2500

The solid fuel industrial furnace Ekozhar Pro Max 2500 is an equipment designed for air heating of complexes of premises up to 610 square meters, as well as for supplying warm air for use in technological processes at industrial, agricultural and repair enterprises.

Inside the furnace, the grate is a special separating structure in the form of a grate of the heating part of the furnace that supports a layer of solid fuel. At the same time, the burnt fuel in the form of ash freely passes through the cracks and openings between the grates, thus not blocking the free passage of air masses. The grate is located between the fuel combustion chamber and the ash compartment. The stove has an ash pan, the door opens for easy maintenance. The ash pan has a slide valve, which can be used to control the air supply to the combustion chamber.

There is also a secondary gas afterburner chamber in the furnace, which is used for the pyrolysis process. The furnace tube itself is finned over the area, which is hidden in a casing, making heat transfer most efficient by increasing the heating area.

Also, a heat exchanger made of finned tubes is mounted in the casing. The door and rear panel can be removed from both sides if necessary, so that it can be cleaned after prolonged use. The diameter of the outlet is 300 mm.

This model should be equipped with a fan, which ensures fast and even heat distribution and allows you to achieve a comfortable room temperature in a short time.

The use of a fan allows you to increase the efficiency of the oven up to 91% and evenly distribute the heated air throughout the room.

Each series and model of our furnaces is developed by a designer to ensure maximum efficiency and productivity. We have mass production of furnaces, which guarantees the quality of each product. And all models of stoves have a certificate of conformity.

We are confident in the quality of our products and that you will be satisfied.

Our customers' feedback serves as confirmation for both us and you.

Below is only a small part of them.

The thickness of the furnace

10 mm

Type of furnace

airborne

Heating volume

2500 cubic meters

Heating area

610 sq.m.

Material