Principle of work and design

ECOZHAR

The principle of operation of the furnace

The principle of operation of the Ekozhar Pro series furnaces is based on forced convection of the heated air. The fan draws cold air from the room and drives it through the coolant circulation chamber between the furnace and the outer casing. In this way, heat is removed from the heated firebox and transferred to the room through the outlet heat pipes. If it is necessary to transfer the heated air to an adjacent room, a metal corrugated pipe is used.

Blower and slide damper

A control valve, a slide damper, is installed in the inlet of the furnace. It allows you to accurately dose the amount of air entering the combustion chamber, thereby optimizing efficiency and increasing the time of fuel combustion on one full load. This damper allows you to precisely adjust the cross-section of the inlet pipe, which allows you to use the stove in two operating modes: combustion mode and smoldering mode.

Firebox thickness

In the Ekozhar Pro series, special emphasis is placed on the thickness of the firebox metal, which is 5 mm. The metal we use guarantees a service life of at least 10 years.

Outer casing

The outer casing is made of 1.5 mm thick sheet metal. This thickness was chosen for a reason. First, it is the optimal thickness that allows the structure to be rigid. Secondly, in this area, the metal is less susceptible to temperature effects than the metal of the furnace. Thirdly, if the casing wall is too thick, it will prevent good heat transfer to the room, which will reduce the efficiency of the furnace as a whole.

The firebox door latch

The firebox door handle acts as a lock in the closed position. In this position, the door is tightly pressed, and due to the sealing cord along the contour of the door itself, flue gases cannot enter the room.

Coolant circulation chamber

The space between the walls of the furnace and the outer casing is the circulation chamber. By forcing air through the circulation chamber, heat is removed from the furnace walls evenly over the entire area. The circulation chamber is physically separated from the combustion chamber and prevents flue gases from entering the room.

Watch a 2-minute video about the Ekozhar Pro series stoves

The Ekozhar Pro 203 vertical heating furnace is designed to heat large rooms with an area of up to 80 m² and a volume of up to 200 m³.

The power of this furnace model is 8 kW, which allows you to quickly heat large spaces, including production halls, warehouses, or even large houses.

The efficiency is 81%.

Burning time on one full load of wood - up to 6 hours

Chimney diameter - 110 mm

Construction of the Ekozhar Pro 230 furnace

The furnace furnace is made of a thick-walled pipe, 5 mm thick. The casing is made of metal, 1.5 mm thick. This is enough for the stove to operate efficiently for more than one season and does not interfere with good heat transfer to the room.

The stove operates in two modes: burning and smoldering. The combustion mode is used to ignite the stove and quickly warm up the room, and the smoldering mode maintains the set temperature after heating, significantly saving fuel. Switching between the modes and adjusting the intensity of combustion is carried out using two slide dampers on the door and chimney pipes.

There is a plate inside the firebox that helps to cool the gases before they enter the chimney, which increases the service life of the chimney and the stove as a whole. The stove door is equipped with a heat-resistant cord that prevents smoke from escaping into the room.

Each series and model of our furnaces is developed by a designer to ensure maximum efficiency and productivity. We have mass production of furnaces, which guarantees the quality of each product. And all models of stoves have a certificate of conformity.

We are confident in the quality of our products and that you will be satisfied.

Our customers' feedback serves as confirmation for both us and you.

Below is only a small part of them.

Our heating stoves use an active heat circuit to distribute heat efficiently and maintain the optimum room temperature, as well as to increase the energy efficiency of the stove. This circuit is a combination of corrugated tubes and a fan connection for blowing around the firebox or along the contour of the stove walls. Thanks to the active heat circuit, the stove can maintain stable heating even after combustion is complete, cooling down more slowly and releasing the accumulated heat. This reduces fuel consumption and ensures constant comfort in the room.

The thickness of the furnace

5mm

Type of furnace

airborne

Heating volume

200m3

Heating area

80m2

Material

steel

Firebox size

600х320mm